Anyone know what type of lights these are? Seem to be some type of embedded ring lights but not sure how to find them.

No idea but it looks like something you'd get from aliexpress by the case. Did you check there?

In case you can't find anything, may be worth looking at cornhole light sets. May not be quite as nice but would be pretty easy to find.

htxag09 said:

---

In case you can't find anything, may be worth looking at cornhole light sets. May not be quite as nice but would be pretty easy to find.

---

good idea! Was able to find some but they're like $16/each. I need to figure out what they are called on aliexpress/bulk options. thanks for the idea

This is really nice. Trying to figure it out - will repost back if I get a genius idea.

First thought was plexiglass sheet sandwiched between plywood sheets, circles drilled out and router a slot for that roll LED light stuff around the inside of the plywood that would reflect thru the plexi edges lighting the holes.

But that plexi or lighting source around the circles looks thicker that the line around the outside that shows a seam or something on the edge of the plywood.

Still thinking.....

chrisag09 said:

---

Might be LED COB strip lights, just not sure how they concealed the wiring so well

---

The piece is three laminated sheets pressed together. The inner sheet is largely hollow. If it's just 2 pieces of plywood, then it's just more router work.
The rings could be plexiglass or perhaps epoxy (sanded on the inside for the matte finish)

https://www.1000bulbs.com/product/96718/FT2-L120FR12150.html#detail-tabs

The spool is expensive, but one of the spec sheets has instructions to cut them.

LED tape light probably.

Looks like a channel routed in the the two pieces of plywood. Then an LED strip pressed or glued into the channel.

chrisag09 said:

---

Might be LED COB strip lights, just not sure how they concealed the wiring so well

---

It's COB lighting.

https://www.amazon.com/Barcaloo-Cornhole-Board-Lights-Lighting/dp/B08L6QSBFL/ref=asc_df_B08L6QSBFL/?tag=hyprod-20&linkCode=df0&hvadid=507718513187&hvpos=&hvnetw=g&hvrand=10626851966269134455&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9027906&hvtargid=pla-1278536825722&psc=1

I've been playing around with LED lighting but have not been back on the project in a bit.

Here are some different items I have ordered that may meet your solution.

For wiring, I imagine its just affixed to on side or the other then use small strips around the edges to create the interior gap whilst concealing gap on outside edge.

Power Supply:
https://www.amazon.com/gp/product/B01LXN7MN3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1

Example of Lights:
https://www.amazon.com/gp/product/B01CDTEJR0/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Infinite choices here depending on brightness, color, number of lights, controllability, etc.

Flexible Channel / DIffuser:
https://www.amazon.com/gp/product/B08QMHMS4H/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Controller:
https://www.amazon.com/gp/product/B07RJXP9NB/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1

Just to give some ideas if you want to go down the led lighting hole.

Lights I included can be cut to length or extended by connectors. You can run LV wires in between lighted areas so you only use the lights where needed.

Have fun!

That's what I was thinking.